我移植2.6内核到2440中，现在已经进入到了系统，但是启动信息有些错误，请高手指点启动信息错误在哪。
*************************************************************>
S3C2440 Bootloader V2006
CPU ID is 0x32440001
Found boot params
FCLK=400MHz, HCLK=100MHz, PCLK=50MHz, CPU is running at 400MHz
UPLL=96MHz, UCLK=48MHz
Serial port 1, Baud rate is 115200.
OS image stored in NAND Flash.
Autoboot delay is 3 seconds.
<*************************************************************>
Check SST39VF160 Flash ID is 0xea000045
NOR Flash Man. ID is 0x90
Unsupported Flash Type!
Fail to write camera IIC!
DIVN_UPLL0
MPLLVal [M:5ch,P:1h,S:1h]
CLKDIVN:dh
+---------------------------------------------+
| S3C2440A USB Downloader ver R0.03 2004 Jan |
+---------------------------------------------+
FCLK=400.0MHz,DMA mode
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3
FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>
NOTE: 1. Power off/on or press the reset button for 1 sec
in order to get a valid USB device address.
2. For additional menu, Press any key.
USB host is not connected yet.
Read chip id = ec76
Nand flash status = c0
Set boot params = root=/dev/mtdblock2 init=/linuxrc load_ramdisk=0 console=ttySAC1,115200 mem=65536K devfs=mount display=dh240
Load Kernel...
Uncompressing Linux...................................................................................................... done, booting the kernel.
Linux version 2.6.12-h1940 (root@localhost.localdomain) (gcc version 3.4.1) #16 Fri Jul 4 10:26:31 CST 2008
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: SMDK2410
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C2440: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
USB Control, (c) 2006 ucdragon yl2440.new
Built 1 zonelists
Kernel command line: root=/dev/mtdblock2 init=/linuxrc load_ramdisk=0 console=ttySAC1,115200 mem=65536K devfs=mount display=dh240
irq: clearing pending ext status 00002000
irq: clearing subpending status 00000092
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00590000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61568KB available (2651K code, 493K data, 156K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, UPLL 96.000 MHz
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver 2.1.22 [Flags: R/W].
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
yaffs Jul 4 2008 10:24:55 Installing.
Initializing Cryptographic API
--- s3c2410fb init ---!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
pxafb_probe start!!!!!!!!!!!!!!!!!!!!!!!!!!
VA=0xffc00000, PA=0x33d40000, size=0x00027000
Console: switching to colour frame buffer device 40x30
success to register framebuffer device: 0!!!
done probe!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
fb1: Virtual frame buffer device, using 1024K of video memory
in s3c2410ts init()
success get major number!!!!!!
s3c2410-ts device driver MAJOR:253
success to get adc clock source!
base_addr = 0xc4962000
line 535 passed!
register s3c2410-ts driver success, return code is 0
S3C2410 RTC, (c) 2004 Simtec Electronics
initialize ST16C550 on yl-2410 board, iobase = 0xd4000000
Serial: 8250/16550 driver $Revision: 1.90 $ ,hace done serial8250_io_init!!!!5 ports, IRQ sharing disabled
have enter serial8250_isa_init_ports!iobase = 0xc4980000
line 2166 passed
line 2168 passed
before uart_configure_port!
line 1958 passed
line 1960 passed
IN!!line 1965 passed
enter uart_report_port() line 1918 passed
ttsA0 at I/O 0xc4980000 (irq = 57) is a 16550A
line 1967 passed
line 1974 passed
line 1976 passed
line 1984 passed
after uart_configure_port!
line 2196 passed
line 2198 passed
line 2166 passed
line 2168 passed
before uart_configure_port!
line 1958 passed
line 1960 passed
IN!!line 1965 passed
enter uart_report_port() line 1918 passed
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
line 1967 passed
line 1974 passed
line 1976 passed
line 1984 passed
after uart_configure_port!
line 2196 passed
line 2198 passed
line 2166 passed
line 2168 passed
before uart_configure_port!
line 1958 passed
line 1960 passed
IN!!line 1965 passed
enter uart_report_port() line 1918 passed
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
line 1967 passed
line 1974 passed
line 1976 passed
after uart_configure_port!
line 2196 passed
line 2198 passed
line 2166 passed
line 2168 passed
before uart_configure_port!
line 1958 passed
line 1960 passed
IN!!line 1965 passed
enter uart_report_port() line 1918 passed
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
line 1967 passed
line 1974 passed
line 1976 passed
line 1984 passed
after uart_configure_port!
line 2196 passed
line 2198 passed
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
ub: sizeof ub_scsi_cmd 68 ub_dev 2384 ub_lun 140
usbcore: registered new driver ub
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
Cirrus Logic CS8900A driver for Linux (V0.02)
dev->base_addr=0xe0000300<3>line 689 passed,request_region() OK!success get IO port address!
eth0: CS8900A rev E detected
BWSCON=2211d110
GPFCON=1a6aaaa
EXTINT0=22122242
INTMSK=6f7f3d9f
BWSCON=221dd110
GPFCON=1a6aaaa
EXTINT0=21122242
INTMSK=6f7f3d9f
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
SET CF & IDE WAIT!now BWSCON=225dd510
now begin cf_ide_init_default_hwifs()
have initialized interrupt for cf:EINT3
fla2612:INTMSK=6f7f3d97
GPFCON=000055aa
EXTINT0=00004040
GPBCON=00100154
GPBDAT=000007e3
-1:no 0
k CF_register_hw return -1
hda: PQI IDE DiskOnModule, ATA DISK drive
hdb: no response (status = 0xa1), resetting drive
hdb: no response (status = 0xa1)
ide0 at 0xc4ae0020-0xc4ae0027,0xc4ae001c on irq 17
-1:no 0
k ide_register_hw return 0
hda: max request size: 128KiB
hda: 128000 sectors (65 MB) w/1KiB Cache, CHS=500/8/32
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 < p5 >
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4b00000
s3c2410-nand: timing: Tacls 10ns, Twrph0 40ns, Twrph1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 1779 at 0x01bcc000
Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00030000 : "Boot modified by fla in devs.c"
0x00030000-0x00200000 : "Kernel"
0x00200000-0x02000000 : "RootFileSystem"
0x02000000-0x04000000 : "ExtendFileSystem"
usbmon: debugs is not available
hello,enter new ohci-s3c2410.c
CLKDIVN = 0000000d
CLKSLOW = 00000004
CLKCON = 00f2eb70
UPLLCON = 00038021
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.12-h1940 ohci_hcd
usb usb1: SerialNumber: s3c24xx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
line 1408 passed!
virtual address of s3c2410_va_iis=f0d00000.
next will do driver_register!
just enter s3c2410_uda1341_probe()
S3C2410-UDA1341 Probe
line 1322 passed!
line 1325 passed!
line 1327 passed! have set L3 mode=GPB2, dat=GPB3, clk=GPB4, output
line 1330 passed!
line 1332 passed!
have set IISLRCK=GPE0, IISSCLK=GPE1, CDCLK=GPE2, IISSDI=GPE3, IISSDO=GPE4
line 1336 passed! have Enable IIS clock
line 1287 passed!
line 238 passed!
line 275 passed!
line 275 passed!
line 275 passed!
line 238 passed!
line 275 passed!
line 275 passed!
line 275 passed!
line 275 passed!
line 275 passed!
line 1309 passed!
success register irq: iisout_dma_done_handler
success register irq: iisin_dma_done_handler
UDA1341 audio driver initialized
driver uda1341 in /sound/oss/s3c2410-oss.c
line 1414 passed!
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
Reading data from NAND FLASH without ECC is not recommended
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 156K
Reading data from NAND FLASH without ECC is not recommended
Reading data from NAND FLASH without ECC is not recommended
Using /usr/usbfor2440.ko
Error -3 while decompressing!
c032c044(1980947191)->c3b52000(4096)
insmod: cannot insert `/usr/usbfor2440.ko': Invalid module format (-1): Exec format error
mount: Mounting none on /proc/bus/usb failed: No such file or directory
Please press Enter to activate this console. cirrus_start: requesting interrupt 53
eth0: register interrupt 53 successfuly
Error -3 while decompressing!
c032bba4(-603116625)->c3bec000(4096)
Error -3 while decompressing!
c0327753(144903922)->c3bed000(4096)
/usr/etc/rc.local: line 8: /usr/sbin/makelinks: cannot execute binary file
ln: /dev/touchscreen/0: File exists
Reading data from NAND FLASH without ECC is not recommended
Could not open mime.types file, "etc/mime.types", for reading
mount: Mounting /dev/nfblock/3 on /tmp/flashdisk failed: No such file or directory
mount: Mounting /dev/nfblock/2 on /tmp/mplayer failed: No such file or directory
Reading data from NAND FLASH without ECC is not recommended
Reading data from NAND FLASH without ECC is not recommended
Reading data from NAND FLASH without ECC is not recommended
Can't open framebuffer device /dev/fb0
Can't open framebuffer device /dev/fb0
driver cannot connect
Please press Enter to activate this console.
ln: /dev/touchscreen/0: File exists
[root@(none) /]# ls
Reading data from NAND FLASH without ECC is not recommended
[1;34mQtopia[0m [1;34mdev[0m [1;34mhome[0m [1;32mlinuxrc[0m [1;36mramdisk[0m [1;32mtestshell[0m [1;34musr[0m
[1;34mbin[0m [1;34metc[0m [1;34mlib[0m [1;34mproc[0m [1;34msbin[0m [1;36mtmp[0m [1;34mvar[0m
[root@(none) /]#
2008-10-23, 07:34 PM
移植问题：
回复: 移植问题S3C44BOX01
平板模式
